Wrap-around Office Space

Zeek wanted a modern looking office space with back-lit LED lighting, wall mounted articulating monitors and configurable shelving. Here is what we came up with.
Zeek wanted a modern looking office space with back-lit LED lighting, wall mounted articulating monitors and configurable shelving. Here is what we came up with.
We started by attaching 2x4 ledgers into the studs with 3 inch screws. A 1x3 was attached to the bottom of the ledger to act as the bottom of a wiring channel. Thin 1 1/2 inch  strips were added the  front of the 1x3 channels after attaching the to the wall to complete the U shaped trough.
We started by attaching 2×4 ledgers into the studs with 3 inch screws. A 1×3 was attached to the bottom of the ledger to act as the bottom of a wiring channel. Thin 1 1/2 inch strips were added the front of the 1×3 channels after attaching the to the wall to complete the U shaped trough.
The sheet on the 8 foot wall was laid with a 16 inch radius (48 inch sheet width - 30 inches desk width) to make a smooth curve onto the 12 foot long wall section. We cut the curve with a sabre saw and outside the layout line and used an oscillating drum sander to smooth the cut to the line.
The sheet on the 8 foot wall was laid with a 16 inch radius (48 inch sheet width – 30 inches desk width) to make a smooth curve onto the 12 foot long wall section. We cut the curve with a sabre saw and outside the layout line and used an oscillating drum sander to smooth the cut to the line.
 A 5/8 inch wide router bit was used to make a channel for the LEDs at the back edge of the sheets of plywood used for the desktop. The channel was just deep enough to accommodate the thickness of the strips (3/16 inch). It was located about 3 inches from the back edge. The factory edge of another sheet of plywood was used as guide for the router base. The width of the desk was 30 inches. It extended 8 feet along one wall and 12 feet along the other.
A 5/8 inch wide router bit was used to make a channel for the LEDs at the back edge of the sheets of plywood used for the desktop. The channel was just deep enough to accommodate the thickness of the strips (3/16 inch). It was located about 3 inches from the back edge. The factory edge of another sheet of plywood was used as guide for the router base. The width of the desk was 30 inches. It extended 8 feet along one wall and 12 feet along the other.
We brushed on a coat of MinWax Polyshades Classic Black on the desktops and followed it up with several coats of polyurethane, doing a light sand between coats. Two 1/8 inch thicknesses of red oak were bent around the inside curve of the desk edge, glued with Titebond III and clamped in place overnight to dry. We used a single 1/4 inch thickness of red oak on the the straight portions of the desk edges. The oak edges were finished with Watco Natural Oil.

Temporary 2×4 braces supported the table tops at the correct height while they were attached to the wall ledgers with countersunk 2 1/2 inch screws. Two inch holes for a couple of black plastic desk cable grommets were drilled at the back edge of the desks, inside the LED recesses.
Four canti-lever braces made from 3/4 inch black pipe fittings replaced the temporary 2×4 bracing under the desktop. They provided enough support to enable a person to sit on the desktop without sagging. Also notice the 5 inch wide plywood plate added underneath the desktop where the two 4×8 foot sheets of plywood butt against one another.
French cleats were made by ripping a 1×4 inch pine board at 45 degrees and mounting the bottom half at two levels on the wall. The upper mating half was reserved for mounting to the backs of shelves, pictures, and any other component that was desired to be hung on the wall.
Book shelves were built in several “tetris” block shapes from the 3/4 inch plywood desktop remnants. A 3/4 inch back provided the needed rigidity to the various shapes. They were primed and painted different colors.
Full motion arm mounts were attached to wall studs to support three computer monitors. They swivel to support monitors in either portrait or landscape orientations and articulate to extend up to 20 inches from the wall.

AmazonBasics Premium Wall Mount Computer Monitor and TV Stand – Lift Engine Arm Mount, Aluminum

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.